Listen to Coronavirus Patient Zero
DIY PC Build - PC Assembly Made Easy
DIY PC Assembly Steps When you have the new PC components items available, next step is to Assemble the PC together. This is the most interesting part and also the most rewarding part when your system is up and running, all credits to Yourself!! Essential Tools required: 1) A screwdriver (Cross-shaped) Optional Recommended Items: 1) Torchlight (To illuminate hard to see areas) 2) Antistatic wrist strap (To discharge of any static charges) Let¡¯s start now. Firstly, discharge yourself of any static charges by touching the metal casing or attaching the other side of the antistatic wrist strap to the metal casing. 1) Open the case 2) Install the motherboard Find the motherboard standoffs that should have come with the case. Insert the I/O Shield that came with your motherboard. Now locate the screw holes on your motherboard and find the corresponding holes on the motherboard plate (or tray) in the case.
Put a standoff in each of these holes on the tray and position the motherboard so that you can see the holes in the top of the standoffs through the screw holes in the motherboard. Now fasten a screw through each of the motherboard screw holes into the standoffs underneath. These screws should be snug but not tight. With the motherboard in, we are now able to start adding in other components. 3) Install the CPU.
As I mentioned earlier, the processor (CPU) and motherboard go hand-in-hand, so you should spend some time planning and researching what you really desires and buy compatible CPU / motherboard components, just like the importance of buying the right shoe size for yourself. Given that this is a minimum system upgrade, you are saving up quite a bit through reusing other components; I suggest you build a better performing system so that it can serve you for several years to come. Before start, please read the manual provided with the motherboard/CPU carefully, understand the different parts, and the installation diagrams before proceeding. Then again, it is not very difficult with only 3 simple steps to success. 1st step to success: Install the CPU I will be using Intel Socket 775 as illustration as it is the latest socket used so far. -Remove the protective socket on the new socket protecting the pins -Open the lever and lift up the metal flap so as to install the CPU -While carefully holding the CPU at the edges, look for the notch in the corner and match it up with the socket. Slowly lay down the CPU in the socket, before lowering the metal flap, and closing the socket lever to secure the CPU. 2nd step to success: Install the CPU heatsink If you like to go to a cool place to enjoy some aircon when you are hot, the same can be said of the CPU which you have just installed. We need to dissipate the high heat generated by the CPU so that it would not overheat and fry. -I am recommending getting hold of some thermal paste which you can apply evenly on the CPU surface for better heat conductivity and dissipation.
(To note: Intel? boxed processor already come with their integrated thermal solutions, and so does not need extra efforts) -Align heat sink onto the Socket containing the CPU, with the fan cable orientated closest to fan power connector, and check for any entanglement. -Press down on fastener caps with thumb to install and lock. Repeat with the other 3 fasteners. 3rd step to success: Power up the heat sink This is done by connecting the fan cable from step 2 to the CPU FAN connector located on the motherboard, which is located very close to the CPU. Tie up excess cable to prevent interference with fan operation or other components. Congrats, by the time you finished this, the rest should be a breeze already =) 4) Install the Memory With a new motherboard and faster processor, we will then need more RAM (random access memory) to enable and facilitate this faster performance. Again, you should spend some time planning and researching on memory which is compatible with the new CPU and motherboard you have installed to bring out the best overall performance. To install the RAM modules, you need to unfasten the clips located on each side of the memory slot. Align the RAM module in the socket, such as to match the indent located on the memory chip and the memory slot, for the right facing direction. Push down on the memory module until both clips refasten and a click sound is heard.
To change memory, simply press down the both clips at the same time, and the RAM will come out easily. TIP: Start adding RAM at the slot labeled ¡°Bank 0¡± or ¡°DIMM 1¡±. If you don¡¯t, the system will think there is no memory available and wont boot. TIP:For newer systems supporting hyper treading technology, you are encouraged to use the dual channel memory functionality by placing 2 sticks of the same memory on alternate slots (i.: slot 1 & 3 or Slot 2 & 4, often differentiated by color as well. ) This has been proven to enhance the performance as well. After installing the new motherboard / CPU, and memory, you are already DONE installing the New essential items you have bought. YEAH!! Now that is left is to migrate the remaining items from the old pc to your "Brand New" PC. =) 5) Install the Power Supply There will be a bracket at the top of the case where you can mount the power supply, and secure the power supply using screws.
The power supply will consists of the following connectors: ATX power connector, ATX 12V connector, IDE power connector, and FDD power connector. Look for the 20 or 24 pin ATX power connector, and plug it into the motherboard allocated power slot. There may also be an additional four or eight pin power lead on the motherboard that needs to be plugged in, which is usually located near the processor socket. Do double confirm with the motherboard manual for details. TIP: You might want to consider getting a new power supply which rating is at least 300W so as to support any future upgrades you have in mind. TIP: You need to select the right power supply settings (115v or 220v) depending on your country settings. For newer power supplies, it is equipped with automatic detection, so that will not be an issue at all. 6) Install the Floppy drives/Hard-disks/DVD writers Floppy disks, Harddisks and DVD ROM/writers communicate with the CPU through data cables commonly called FDD/IDE cables, although newer harddisks now connect via SATA cables for faster data communications. Note: FDD Cable for floppy disk drives appears smaller and has fewer wires.
Ram Mounts Articles
Ram Mounts Books